CD Soundmachine
AZ1123W
User manual
2
7
3
4
X
PRO
5
6
REP ALL
SHUF
Important notes for users in the U.K.
Mains plug
This apparatus is fitted with an approved 13 Amp plug.To change a fuse in this type of
plug proceed as follows:
1. Remove fuse cover and fuse.
2. Fix new fuse which should be a BS1362 3 Amp, A.S.T.A. or BSI approved type.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut off and an
appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a
value of 3 Amp. If a plug without a fuse is used, the fuse at the distribution board
should not be greater than 3 Amp.
Note:The severed plug must be disposed of to avoid a possible shock hazard should it
be inserted into a 13 Amp socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with the following code: blue = neutral (N),
brown = live (L). As these colours may not correspond with the colour markings iden-
tifying the terminals in your plug, proceed as follows:
•
•
•
Connect the blue wire to the terminal marked N or coloured black.
Connect the brown wire to the terminal marked L or coloured red.
Do not connect either wire to the earth terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
Before replacing the plug cover, make certain that the cord grip is clamped over the
sheath of the lead - not simply over the two wires.
Copyright in the U.K.
Recording and playback of material may require consent. See Copyright Act 1956 and
The Performer’s Protection Acts 1958 to 1972.
English
Controls/Power Supply
CAUTION
Supplied Accessories
– AC power cord
Use of controls or adjustments or
performance of procedures other
than herein may result in unsafe
operation.
Top/front panels (See 1)
1
2
Source selector: CD, FM, MW, OFF
This set complies with the radio
interference requirements of the
European Union.
–
selects CD, or radio (FM/MW) source of
sound
–
power off switch
2; - starts or pauses CD playback
Power Supply
§
∞
Whenever convenient, use the power supply
cord if you want to conserve battery life.
Make sure you remove the plug from the set
and wall outlet before inserting batteries.
–
selects the next/previous track
– searches forwards/backwards (press and
hold the button) within the current track
PROG – programs tracks and reviews the
Batteries (not included)
program
1
2
Open the battery door and insert 6 batteries,
type R-14, UM-2 or C-cells, (preferably
alkaline) with the correct polarity as indicated
by the "+" and "–" symbols inside the com-
partment. (See 1)
9
–
–
stops CD playback;;
erases a CD program
3
4
Display
–
shows the CD functions
REPEAT
–
repeats a track/
CD program/entire CD.
Replace the battery door, making sure the bat-
teries are firmly and correctly in place.The set is
now ready to operate.
5 SHUFFLE – plays all tracks in random order
6 OPEN•CLOSE – opens/ closes the CD
door.
7 TUNING – tunes to radio stations
Batteries contain chemical substances, so
they should be disposed of properly.
8
VOLUME
–
adjusts volume level.
•
•
Incorrect use of batteries can cause
electrolyte leakage and will corrode the
compartment or cause the batteries to burst:
Back/bottom panels (See 1)
9 Telescopic antenna - improves FM
reception.
Do not mix battery types: e.g. alkaline with car-
bon zinc. Only use batteries of the same type
for the set.
0 Battery door - open to insert 6 x 1.5V
R-14/ UM-2/ C-cells
•
•
When inserting new batteries, do not try to mix
old batteries with the new ones.
! p – 3.5 mm stereo headphone socket
Helpful hints: The speakers will be muted
when headphones are connected to the set.
Remove the batteries if the set is not to be used
for a long time.
@ AC MAINS~ - inlet for power cord.
Power Supply
General Operation/Tuner
General operation
Using AC power
WARNING:Always check you have
completely switched off the set, before
you change or disconnect power supply.
Switching on and off and selecting the
function
1
2
To select your sound source, adjust the
Source selector to: CD, FM or MW.
1
2
Check if the power voltage, as shown on
the type plate located on the
bottom of the set, corresponds to your
local power supply. If it does not, consult your
dealer or service center.
To switch off the set, adjust the Source
selector to OFF position
Connect the power cord to the AC
MAINS~ inlet and the wall socket.The set is
now connected and ready for use.
Adjusting volume
Adjust the sound with the VOLUME con-
trols.
3
4
To switch the set off completely, withdraw the
power cord from the wall socket.
Install the unit near the AC outlet and where
the AC power plug can be easily reached.
Radio reception
1
2
Adjust the Source selector to FM or
MW to select your desired
waveband.
•
Disconnect the power cord from the wall
socket to protect your set during heavy thun-
derstorms. Children could seriously injure
themselves as the free end of the cable may
still be live if only the connector is removed
from the MAINS socket at the back of the
unit.
Turn TUNING to tune to a station.
Helpful hints:
To improve radio reception
The type plate is located on the
bottom of the set.
•
For FM, extend, incline and turn the telescop-
ic antenna for best reception. Reduce its
length if the signal is too strong.
Helpful hints:
•
For MW, the set uses a built-in antenna.
Direct this antenna for best reception by
turning the whole set.
–
To avoid unnecessary energy consumption,
always adjust the Source selector to OFF
after using the set.
CD Player
Playing a CD
This CD player plays Audio Discs including
CD-Recordables (CD-R) and CD-Rewritables
(CD-RW).
Finding a passage within a
track
During playback, press and hold ∞ or § .
➜ The CD is played at high speed and with
reduced volume.
•
•
1
2
MP3, CD-ROM, CD-I, CDV,VCD, DVD or
computer CDs are not possible for playback.
When you recognize the passage you want,
release ∞ or § to resume normal playback.
IMPORTANT!
Helpful hints:
CDs encoded with copyright protection
technologies by some record companies may
be unplayable by this product.
–
When your searching reaches the end of the
last track, the CD goes to stop mode.
1
2
3
Adjust the Source selector to CD.
Open the CD door
Programming track num-
bers
You may store up to 20 tracks in the desired
sequence. If you like, store any track more
than once.
Insert a CD with the printed side facing up,
then press the CD door gently to close.
➜ Display shows --, and later the total
number of tracks. (See 2)
3
4
Press 2; to start playback.
1
In the stop position, press PROG to
activate programming.
To pause playback, press 2;
.
➜ Display: PROG and 00 flash. (See 4)
➜
Display: 2 flashes. (See 3)
2
3
Press
number.
∞
or
§
to select your desired track
5
6
To resume, press 2; again.
To stop CD playback, press
9.
Press PROG to store the desired track
number.
Helpful hints:
➜ Display: PROG and 00 flash for you to
program the next track..
CD play will also stop when:
–
–
–
you open the CD door;
4
Repeat steps 2 to 3 to select and store all
desired tracks in this way.
➜ If you attempt to store more than 20
tracks, no track can be selected and the
display shows --.
you select FM, MW or OFF sound source;
the CD has reached the end.
5
To play your program, press 2;
.
Selecting a different track
Helpful hints :
•
•
Press ∞ / § once or repeatedly until the
desired track number appears in the display.
In the pause/stop position, press 2; to start
playback.
–
When playback of your program comes
to the stop position, your set will return
to normal playback.To re-enter program
mode, press PROG in the stop position.
CD Player
Reviewing the program
In the stop position, press PROG repeatedly
to see your stored tracks.
Different play modes:
REPEAT. and SHUFFLE
(See 5, 6)
REPEAT
You can play the current track or the whole
disc repeatedly, and combine REPEAT modes
with PROGRAM.
Erasing a program
You can erase the contents of the memory
by:
REP – plays the current track continuously.
– in the stop position, press PROG to enter
program mode, and then press 9.
REP ALL – repeats the entire CD/program
To select play mode, press REPEAT once or
more.
➜ The display shows REP or REP ALL.
Press 2; to start playback if in the stop/pause
position.
To return to normal playback, press REPEAT
repeatedly until the modes are no longer dis-
played.
1
– selecting FM, MW or OFF sound source;
– opening the CD door;
2
3
– You can also press 9 to cancel your play
mode.
SHUFFLE
You can play all the tracks in random order.
1
2
In the stop position, press SHUFFLE to
switch on shuffle play.
➜ Display shows SHUF.
To switch off shuffle play, press 9.
Helpful hints:
–
During the shuffle play, when REP function is
selected, it will play the current shuffled track
repeatedly, or when the REP ALL function is
selected, it will repeat the shuffle play of the
entire CD.
–
Shuffle play is not available in the program
mode.
Maintenance & safety
(See 7)
•
Where the MAINS plug or an appliance cou-
pler is used as the disconnect device, the dis-
connet device shall remain readily operable.
CD player and CD handling
•
If the CD player cannot read CDs correctly,
use a cleaning CD to clean the lens before
taking the set to repair.
•
Do not expose the set, batteries, CDs to
humidity, rain, sand or excessive heat caused
by heating equipment or direct sunlight.
•
•
The lens of the CD player should never be
touched!
•
•
The apparatus shall not be exposed to drip-
ping or splashing.
Sudden changes in the surrounding
temperature can cause condensation on the
lens of your CD player. Playing a CD is then
not possible. Do not attempt to clean the
lens but leave the set in a warm environment
until the moisture evaporates.
Adequate ventilation with a minimum gap of
15cm (6 inches) between the ventilation
holes and surrounding surfaces is necessary
to prevent heat build-up.
•
Do not cover the ventilation openings with
items such as newspapers, table-cloths, cur-
tains, etc.
•
•
Always close the CD-tape door to avoid dust
on the lens.
To clean the CD, wipe in a straight line from
the center towards the edge using a soft,
lint-free cloth. Do not use cleaning agents as
they may damage the disc.
•
•
•
No objects filled with liquids, such as vases,
shall be placed on the apparatus.
No naked flame sources, such as lighted can-
dles, should be placed on the apparatus.
•
•
Never write on a CD or attach any stickers
to it.
The mechanical parts of the set contain
self-lubricating bearings and must not be oiled
or lubricated.
•
To clean the set, use a dry cloth. Do not use
any cleaning agents containing alcohol,
ammonia, benzene or abrasives as these may
harm the housing.
Safety information
Place the set on a flat, hard and stable surface
so that the system does not tilt.
Disposal of your old product
Your product is designed and manufactured with high quality materials and
components, which can be recycled and reused.
When this crossed-out wheeled bin symbol is attached to
a product it means the product is covered by the
European Directive 2002/96/EC.
Please inform yourself about the local separate collection system for electrical
and electronic products.
Please act according to your local rules and do not dispose of your old products
with your normal household waste.The correct disposal of your old product will
help prevent potential negative consequences for the environment and human
health.
Troubleshooting
If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service centre.
WARNING:
Do not open the set as there is a risk of electric shock. Under no
circumstances should you try to repair the set yourself, as this will
invalidate the guarantee.
Problem
Poor radio reception
– Weak radio signal
• FM:Adjust the FM telescopic aerial
– Possible cause
• Remedy
--indication
No sound /power
– No CD inserted
– Volume not adjusted
•
Insert a CD
– CD badly scratched or dirty
Replace/ clean CD, see Maintenance
• Adjust theVOL
– Power cord not securely connected
• Connect the AC power cord properly
– Batteries dead/ incorrectly inserted
• Insert (fresh) batteries correctly
– Headphones connected to the set
•
– Laser lens steamed up
• Wait until lens has cleared
– CD-R/CD-RW is blank or not finalized
•
Use a finalized CD-R/CD-RW or suitable CD
Audio disc only.
•
Disconnect headphones.
– CD contains non-audio files
Note:
• Press ∞ , § once or more to skip to a CD audio
track, instead of the data file.
Make sure the CD is not encoded with
Copyright protection technologies, as some
do not conform to the Compact Disc stan-
dard.
Display does not function properly / No
reaction to operation of any of the
controls
The CD skips tracks
– Electrostatic discharge
– CD damaged or dirty
• Switch off and unplug the set. Reconnect after a
few seconds´´
• Replace or clean CD
– Program/Shuffle is active
• Quit program/shuffle mode
Severe radio hum or noise
Note: A CD badly scratch or dirty may result in
improper operation.
– Electrical interference: set too close to TV,VCR or
computer
• Increase the distance
Environmental information
All unnecessary packaging material has been omitted.The packaging can be easily separated
into three materials: cardboard, polystyrene and plastic.
Your set consists of materials which can be recycled if disassembled by a
specialized company. Please observe the local regulations regarding the
disposal of packaging, dead batteries and old equipment.
Hearing Safety
Listen at a moderate volume.
•
•
Using headphones at a high volume can impair your hearing. This product can produce sounds in
decibel ranges that may cause hearing loss for a normal person, even for exposure less than a
minute. The higher decibel ranges are offered for those that may have already experienced some
hearing loss.
Sound can be deceiving. Over time your hearing "comfort level" adapts to higher volumes of
sound. So after prolonged listening, what sounds "normal" can actually be loud and harmful to
your hearing. To guard against this, set your volume to a safe level before your hearing adapts and
leave it there.
To establish a safe volume level:
•
•
Set your volume control at a low setting.
Slowly increase the sound until you can hear it comfortably and clearly, without distortion.
Listen for reasonable periods of time:
•
•
Prolonged exposure to sound, even at normally "safe" levels, can also cause hearing loss.
Be sure to use your equipment reasonably and take appropriate breaks.
Be sure to observe the following guidelines when using your headphones.
•
•
•
•
•
Listen at reasonable volumes for reasonable periods of time.
Be careful not to adjust the volume as your hearing adapts.
Do not turn up the volume so high that you can't hear what's around you.
You should use caution or temporarily discontinue use in potentially hazardous situations.
Do not use headphones while operating a motorized vehicle, cycling, skateboarding, etc.; it may
create a traffic hazard and is illegal in many areas.
Meet Philips at the Internet
W
CLASS 1
LASER PRODUCT
AZ 1123W
Printed in China
PDCC-JH/ZH-0727
|