OWNER'S MANUAL
C a r A u d i o H i f i S y s t e m
DVD/VCD/CD/MP3 PLAYER
PLD182
Safety precautions
WARNING
CAUTION
To prevent injury or fire,Please
take the following precautions:
Do not operate when driving.
To prevent damage to the machine, Attaching panel:
take the following precautions:
To prevent electric,etc,Please do not
let the metal goods(silver,coin,tools..)fall into
the installation.
If you smell or see smoke,turn off the
power immediately and consult our dealer.
Be careful not to drop or shock the unit
strongly.
Do not touch the liquid crystal to avoid the
life hurt.If the clothes is stained with it,Please
clean it immediately by soap.
For your driving safety,please link your
brake detecting wire with low power
level,and keep it controlled by manual brake
switch.when driving a car,the brake wire shall
be high power level and now,unit can not
play DVD or VCD disc.
Attach the front panel by fixing the left
Be sure the unit is connected to a 12V
DC power with a Negative Ground.
Do not install the unit in places where
it is exposed to direct sunlight,high heat
or humidity,water splash or dust.
To change fuse,please use the same
one in specification and capacity.
When changing fuse,please do it
after pulling down power wires to avoid
short circuit.
Side of it into this unit as 1 showing.
Then push the right side of panel
towards into connecting plug as 2
showing.
Attaching panel
If the unit seems not work in proper
situation,please press the reset button to
resume the function.
2
Electric Connection
CAR AANNTTEENNNNAA
White
RED RRCCHHoouutt
WHITE LLCCHHoouutt
To ffrroonntt lleefftt
FRONT.L
speaker
White/Black
YELLOW VVIIDDEEOO
Gray
Connect ttoo ccoonnttrrooll ffoorraanntteennnnaa
(Blue)
To ffrroonntt rriigghhtt
speaker
or rreemmoottee ccoonnttrrooll ffoorraammpplliiffiieerr..
FRONT.R
REAR.L
Gray//Blacck
Lgnition kkeeyy
switch
Lgnition wwiirree((RReedd))
Battery wwiirree((YYeellllooww))
Green
To rreeaarr lleefftt
speaker
Green//Black
Car ffuussee
box
Car ffuussee bbooxx
(Mainn ffuussee))
Ground wwiirree((BBllaacckk)) ((TTooccaarrcchhaassssisis))
Purple
To rreeaarr rriigghhtt
speaker
Battery
REAR.R
Purplee/Black
3
Installation
Before installing the receiver permanently, fit it in the approximate place in your car ,and connect the
equipment according to the speakers and electrical connections. When
your system is operated properly,(preferably with the
car engine running), follow the instructions
3)Support strap
for permanent installation
(supplied)
of your system.
INSTALL THE UNIT
1)Install half sleeve, can be with or
without adapter. It will fit better
with adapter.
2)Bend over some tabs to secure the
half sleeve inside of dash.
3) Support strap to be strutted under
dash, secure this strip to avoid skipp
ing of disc.
2)Bend over tabs
of half sleeve
(supplied)
1) Adapter
(not supplied)
Half sleeve
(supplied)
REMOVE THE UNIT
Insert removal wrench into the small
gap on the right side of the unit and pull
the unit slightly out on the same side,
then release the wrench. Repeat the
same action for the left side. By now,
you can remove the unit and unplug
the wires connector.
4) Two wrenches for releasing
the unit (supplied)
4
General Features
P/N
RELEASE
VOL+ VOL-
MODE
CLOCK
Volume
Increasing volume
Press the VOL+ button in
clockwise direction.
VOL+
VOL-
BAND
MODE
VOL+
VOL-
SEEK
Decreasing
PWR
EQ3
1
2
STOP
3
RPT
4
RDM
5
6
R.SCN
MUT
ST
LOC
Press the VOL- button in
anticlockwise direction.
SELECT POWER
EQ3
MUTE
Eject
Out
Press the [ ]button to eject the disc out of the unit .
[
]
EJECT
Power
Release
Press the [PWR]button to turn on/off the unit.
press the "
" button to release faceplate.
5
General Features
Hour
MODE
Press the VOL+/- button to set the hour.
Selecting radio and play
Each time you press the key,it will switch between radio
position and disc position.
Minute
Press the VOL+/- button to set the minute.
Quit clock set mode
there is no operation in 5 seconds, it will quit clock
set mode.
P/N
Press [BAND]button
In video mode, press the [BAND] button to exchange between
the PAL and NSTC.
EQ3
Press EQ3 button once to effect [ROCK[ volume, LCD shows
ROCK on.
Press EQ3 button twice to effect [POPS] volume, LCD
shows CLASSICE on.
Mute
Press EQ3 button third to effect [CLASSIC] volume, LCD
shows POP on.
Short press this button to mute the sound, short press
MUTE buttonagain or press any other button to
resume the normallistening.
Press EQ3 button fourth to effect [FLAT] volume, LCD shows
FLAT on.
Press EQ3 button again to resume the normal listening.
Clock
Short press CLK can display time even power off .
Long Press CLK for 3 seconds will enter set mode.
6
Speaker setting
VOL+ VOL-
Speaker mode
VOLUME
BASS
TREBLE
BAND
MODE
VOL+
VOL-
SEEK
PWR
EQ3
1
2
STOP
3
RPT
4
RDM
5
6
R.SCN
MUT
ST
LOC
FADER
BALANCE
SELECT PLAY/PAUSE
STOP REPEAT RANDOM
Volume set mode
Treble set mode
Press SEL button once,display shows VOL
then press the volume button
to adjust volume level up.press
the volume buttonto
,
+
Press SEL button third,
display shows TRE ,then
press the volume
level up. Press the volume
treble level down.
TRE 5
-
+
button to adjust treble
buttonto adjust
adjust volume
level down.
VOL+
-
VOL 10
Balance set mode
Press SEL button fourth
display shows BAL ,then
VOL-
press the volume
to adjust left speaks level .
Press the volume button
to adjust right speaks level .
+
button
Bass set mode
BAL 4
Press SEL button twice,display shows BAS
then press the volume button to adjust bass
button to adjust
,
-
+
level up. Press the volume
bass level down.
-
Fader set mode
Press SEL button fifth,display shows FAD ,then
press the volume button to adjust front speaks
BAS -6
+
level. Press the volume
speaks level.
-
buttonto adjust back
FAD -3
7
Play control
Random
Play/pause
Play
Press [RDM]button
If with DISC in unit,Press the [
]to pause music.
Press this button to play all the track in random order. Press it again
to stop random playing. This button is invalid if the unit is in
PBC On mode.
Pause
Press the [
]button again , come back DISC playing.
If a disc is loaded,a sector sign will show on the display.
Stop
Press [STOP]button
Press STOP
button to stop music,and press
button
to start playing from track one.
Repeat
Press [RPT]button
Press the button to repeat the same track continuously,
RPT will appear on the LCD display.
Press the button again to come back normal playing.
8
Radio Operation
APS
SEEK+
Tuner
manual tuning:
short press
Short press
button it can select higher frequency station.
can select lower frequency station.
VOL+
VOL-
BAND
MODE
SEEK
Auto loading tuning:
the long press
button it can automatically select higher
PWR
EQ3
1
2
STOP
3
RPT
4
RDM
5
6
R.SCN
MUT
ST
LOC
frequency station. And the long press
select lower frequency station.
it can automatically
R.SCN
ST LOC SEEK-
PRESET MEMORY 1-6
St
Band
In FM band mode,press the ST key.
Selecting band
Each time you press the key,you switch between MONO
position andstereo position
Press BAND button to select among three FM or two AM bands.
(FM1-FM2-FM3-AM1-AM2)
if the unit has received stereo signal in FM band in stereo position.
FM1
FM2
FM3
The LCD indicate
ST only.
.If the signal is MONO ,It indicate
AM2
AM1
Select station
Press [APS]button
Loc
Seek Tune:
In radio mode,press this button to toggle between LOC/DX
functions and LOC shown on the display indicates that
LOC function is on.
In FM (FM1 FM2 FM3) or AM(AM1 AM2 playing mode, long
press "APS" button, it can seek and store strong frequecy
station automatically in to1-6 memory buttons.
LOC is local frequency receipt
DX is distance frequency receipt
FM can be memorized 18 stations. AM can be memorized 12 stations.
9
Remote control
Loading and replacing the battery
Use one lithium battery(CR2025)
MODE
CLK
Insert the batteries with the +and - poles aligned properly.
Following the illustration inside the case.
EQ
OSD
Pull out
WARNING
Store unused batteries out of the reach of children.contact a
doctor immediately if the battery is accidentally swallowed.
Do not set the remote on hot places such as the above dashboard.
Title
Angle
Audio
AF
TA
PTY
10
Basic operation
POWER
BAND P/N
Press this button to turn on/off the unit.
Under receiving position,press this button can select band;
under VCD,DVD position,press this button can select
automatic,PAL or NTSC.
DSP
Press this button can show the time,and long press to enter clock
adjustment.
VOL+/VOL-
Press this button can increase or decrease volume.
MODE
LOC/RDM
Press this button can select needed receiving and playing mode.
Under receiving position,press this button can do far and close
switch;under VCD,CD playing,press this button can play randomly.
EQ
Press this button can select mode as POPS,JAZZ,ROCK,DSP OFF.
Stop
Play/pause
Press this button to stop playing.
Press this button can switch between play and pause.Under
stop state, similarly press it to play.
SEEK+/SEEK-
Press this button can manually search tune,fast,back and track
searching control.
ST/PROG
SEL
Under receiving state,press this button can select stereo or single
track;under playing state,it can do programme play cooperating
with STOP button.
Repeatfully press this button can select needed mode.
11
Basic operation
PBC
When playing VCD,OK disc,press this button can show all the
prgramme menu,and can cooperate numeral buttons to select
programmes.
MODE
CLK
OSD
EQ
[ENTER]
[ ][ ][ ][ ]
Under DVD mode, press this button can move cursor in
up,down,left and right directions after entering SETUP
Menu.Press ETR button can confirm selected item.
Title
Angle
AMS/RPT
Under receiving state,press this button can scan memory
stations.Long press it can automatically scan and store them.
Audio
AF
TA
PTY
SETUP
Under playing mode,press this button can open SETUP Menu.
TITLE
Under VCD mode,press this button to enter Menu selection same as
PBC.
Under DVD mode,press this button to return to the top of Menu.
ZOOM
Press this button can zoom picture.
12
Basic operation
ANGLE
Under DVD mode,press this button can change visual angle.
MODE
CLK
SLOW
Under VCD mode,press this button can advance slowly.
Under DVD mode,press this button can advance and back off slowly.
EQ
OSD
SUBTITLE 0-10+
Under DVD mode,press this button can switch dialogue language.
Press this button can directly select track and chapter,and 1-6
buttons can select preseted stations.
AUDIO
Under VCD mode,press this button can switch track.
Under DVD mode,press this button can switch dialogue language.
Title
Angle
MUTE
Press this button to turn off volume out ,and again to resume.
Audio
OSD
AF
TA
PTY
Press this button can show play time, surplus time.
13
Basic operation
Display Setup Menu
Setup Menu for Universal Capability
Press SETUPP,screenn will show system setup menu as follows:
Press[
Press[
Press[
] [
]select Menu
Press[
Press[
Press[
] [
]select Menu
] retutn to Menu
] Enter Menu
] retutn to Menu
] Enter Menu
Press[ENTER] to confirm
Press[ENTER] to confirm
LANGUAGE
DISPLAY
Menu Language
Disc Audio
English
Original
Off
TV Aspect
Display Mode
TV Output
16:9
Widescreen
NTSC
Disc Subtitle
Disc Menu
Original
Move
Select
Move
Select
14
Basic operation
Audio Setup Menu
Lock Setup Menu
Press[
Press[
Press[
] [
]select Menu
Press[
Press[
Press[
] [
]select Menu
] retutn to Menu
] Enter Menu
] retutn to Menu
] Enter Menu
Press[ENTER] to confirm
Press[ENTER] to confirm
LOCK
AUDIO
Rating
Unlock
New
Dolby Digital
DTS
Bitstream
Bitstream
On
Password
Country
U
S
DRC
Digital Output
On
Move
Select
Move
Select
15
Basic operation
Mp3 menu
Insertt MMPP33 ddiisscc,,aannddTTVVwwiillllsshhoowwmmeennuuaassfofolllolowwss: :
Others Setup Menu
Press[
Press[
Press[
] [
]select Menu
Music
] retutn to Menu
] Enter Menu
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
Program
List
1-001_______MP3
Press[ENTER] to confirm
2-002_______MP3
3-004_______MP3
XXXXX________XXX
XXXXX________XXX
XXXXX________XXX
0:01:44
2/135
OTHERS
\001_______MP3
Load Defanlt
Screen Saver
Select
On
In this menu,the right is the submenu of the left,and it can
[ ][ ][ ][ ]
cooperate remote control
buttons to select
wanted contents and programmes and press ENTER to
confirm.
Move
Select
16
Accessories
External view
External view
........ Number of items
........ Number of items
1
3
2
............1
............2
............1
The use of any accessories except of those provided
might result in damage to the unit .Make sure only to
use the accessories shipped with the unit ,as shown
above.
17
Specifications
Specifications subject to change without notice.
CD PLAYER
GENERAL
Signal/Noise radio......................................................70dB
Frequency response..............................20Hz-20KHz(+3dB)
Channel separation..................................................>45dB
Dual D/A converter......................................................16Bit
Operating power....................................12 Volts DC,negative
ground
%10THD output wiring.........................Designed for using four
speakers only front and rear
channels cannot be combined
in use with 2speakers.
FM Tuner
Load impedance..................................compatible 4 to 8 ohm
speakers
Tuning range..................................EUROPE:87.5-108.0MHz
(50KHz step)
USA:87.5-108MHz
(100KHz step)
Fuses............................................................ ..........10 amp
Dimensions...........................................178mm(L)x50mm(W)
x150mm(H)
Weight......................................................................2.5Kgs
FM usable sensitivity(S/N=30dB)...............................<12dB
Stereo separation......................................................>45dB
AM Tuner
Tuning range.....................................EUROPE:522-1620KHz
(9KHz step)
USA:520-1720KHz
(10KHz step)
AM sensitivity..............................................................28dB
18
Trouble shooting guide
What might seem to be a malfunction in your unit may just be the result
of slight misoperation or miswiring.Before calling service, first check the
following table for possible problems.
?No/Poor sound on one or more speakers
Speakers or speaker wiring or volume, Balance and
Fader setting
?The power does not turn ON.
Check the speaker wiring and test the speakers all in good condition
check the setting of volume, Balance and Fader controls.
The fuse has blown.
Confirm whether the lead short circuit,then replace fuse with same capacity.
?CD sound skips
?NO Sound.
The cable connect incorrectness.
Installation the unit angle is greater than 45 ,or
Exactitude connect of the cable.
mounting is not fixed and the back strap is not secure.
Adjust the unit with mounting angle less than 45 and make sure the
unit is mounted securely and tighten with the back strap(supplied)
?Noise on Radio or poor recepiton
Antenna and Antenna Cable.
Check antenna and antenna cable, the antenna base must be
grounded and connected with good condition, replace
antenna or antenna cable if needed.
?Unit completely inoperative, no Light and Sound
Incorrect wire connection, Power RED/YELLOW or
Ground wire or Blown fuse
Check the Red wire to +12 Volts with key lgnition witch, yellow wire to
+12 Volts battery and black wire to ground. Check Fuse with red/yellow
wire, or check the fuse block on your car.
?Noise on both Radio and CD
Poor ground,dirty or corroded at the car Battery posts
Check the black wire for proper grounding clean and tighten ground
connection.
19
OWNER'S MANUAL
Before installation and operating the unit please read
this manual thoroughly and retain
it for future reference
|